• Lietuvių
    • English
  • Lietuvių 
    • Lietuvių
    • English
  • Prisijungti
Peržiūrėti įrašą 
  •   DSpace pagrindinis
  • Mokslinės publikacijos (PDB) / Scientific publications (PDB)
  • Konferencijų publikacijos / Conference Publications
  • Konferencijų pranešimų santraukos / Conference and Meeting Abstracts
  • Peržiūrėti įrašą
  •   DSpace pagrindinis
  • Mokslinės publikacijos (PDB) / Scientific publications (PDB)
  • Konferencijų publikacijos / Conference Publications
  • Konferencijų pranešimų santraukos / Conference and Meeting Abstracts
  • Peržiūrėti įrašą
JavaScript is disabled for your browser. Some features of this site may not work without it.

Investigation of polishing quality of optical surfaces at small samples

Thumbnail
Data
2020
Autorius
Švagždytė, Ieva
Jarmolajeva, Ela
Borodinas, Sergejus
Jurevičius, Mindaugas
Metaduomenys
Rodyti detalų aprašą
Santrauka
Flat elements are often used in optics. The most well-known are prisms, mirrors, and beam splitters. In order to produce high quality optical elements, the finishing process - polishing - is one of the most important processing steps. The purpose of this experiment was to determine the variation of two surface quality parameters, flat PV and waviness RMS, at different cutting rates. Blanks of optical glass BK7 were used for the experiments. Three parameters of cutting rates were changed: clamping force, polishing pad speed and polishing time. Each of these parameters had three values. At the lightest, medium and heaviest cutting rates, 6 flat surfaces were polished in each case for a total of 18 samples. The obtained measurement results were evaluated by the Shapiro-Wilk test. This is a normal distribution test that is used with a small number of tests. The smallest deviation from the flatness PV (1.3 μm) was obtained at the lowest cutting rates, when the lowest clamping force and rotation sped up. The parameters of this deviation almost doubled (up to 4.2 μm) when the polishing pad rotated at the maximum speed selected and under the maximum load. The surface waviness in RMS followed the same trend (the lowest obtained value was 0.3 mm, and maximum value was 1.2 μm). However, the obtained values increased more slowly with the cutting rates. Such variation in the results may be due to vibrations in the machining area.
Paskelbimo data (metai)
2020
URI
https://etalpykla.vilniustech.lt/handle/123456789/150447
Kolekcijos
  • Konferencijų pranešimų santraukos / Conference and Meeting Abstracts [3431]

 

 

Naršyti

Visame DSpaceRinkiniai ir kolekcijosPagal išleidimo datąAutoriaiAntraštėsTemos / Reikšminiai žodžiai InstitucijaFakultetasKatedra / institutasTipasŠaltinisLeidėjasTipas (PDB/ETD)Mokslo sritisStudijų kryptisVILNIUS TECH mokslinių tyrimų prioritetinės kryptys ir tematikosLietuvos sumanios specializacijosŠi kolekcijaPagal išleidimo datąAutoriaiAntraštėsTemos / Reikšminiai žodžiai InstitucijaFakultetasKatedra / institutasTipasŠaltinisLeidėjasTipas (PDB/ETD)Mokslo sritisStudijų kryptisVILNIUS TECH mokslinių tyrimų prioritetinės kryptys ir tematikosLietuvos sumanios specializacijos

Asmeninė paskyra

PrisijungtiRegistruotis